Data East small DMD

Vragen en antwoorden over de technische kant van flippers
Plaats reactie
Gebruikersavatar
vanlierde51
Berichten: 522
Lid geworden op: 25 feb 2014, 08:32
Real name: Gilles Van Lierde
Locatie: Belgium

Data East small DMD

Bericht door vanlierde51 » 03 jan 2018, 22:29

Hooi,

Heb hier een DE Star Trek met de smalle DMD.
Ik krijg midden en links 2 verticale lijnen van 2cm breed, that's it. Na enkele seconden verdwijnen ze en zijn er enkel een paar puntjes nog te zien.
Voeding is nagekeken en ok. CPU boot compleet.
Display dood?
Gilflip
BOP, FT, JP, DW, Radical, DrWho, SMania,BSD,DLady,GWings, Space T,GLizard, JITB,Blue Rib,Pharaoh,T-Zone,Pol Force,CBWizard,Bad girls,TM, DM, DW, SK, PB35th- neo-geo 120 in 1, Brabo 60 in 1, Carn-Evil, Offroad Rally

Gebruikersavatar
Vic
Berichten: 444
Lid geworden op: 16 jan 2014, 12:08
Real name: Eric
Locatie: Belgium

Re: Data East small DMD

Bericht door Vic » 04 jan 2018, 09:06

Werken de insert lampjes ?

Als de +18v voor de inserts niet aanwezig is gaat de display ook niet werken (Een Data East enigenaardigheidje).
De +12V voor het display wordt van het +18V lamp cirquit gemaakt.

Veel kans dat de spanningen voor het display ergens niet goed zijn.
I knew I should have brought another t-shirt

Gebruikersavatar
Bos007
Berichten: 491
Lid geworden op: 21 aug 2011, 11:13
Real name: Andy Bostyn
Locatie: Belgium

Re: Data East small DMD

Bericht door Bos007 » 04 jan 2018, 09:27

soortgelijk probleem gehad (random brol op het scherm)
bleek r95 te zijn (thx Clay)

A very common problem on the small 16x132 displays (as used on five games, Checkpoint to Batman) is a failed R95 resistor. It is very common for this 33k, 1/2 watt resistor to go out of spec, or even open. This will cause the display to look garbled. Often the display itself is fine; it's just this resistor that needs to be replaced.

When replacing the resistor, it is best to just cut the old R95 resistor out, closest to the resistor itself. Then solder the new resistor to the old "legs". It is very easy to tear the traces when removing the old R95 lead. This technique will prevent that.

If after replacing R95 the display is still garbled, check for torn traces. The top lead of R95 connects to the top lead of R94. The bottom lead of R95 connects to the top lead of transistor Q2. If continuity is not detected between these points, replacing R95 won't change anything until the torn trace(s) are repaired.

maralb
Berichten: 128
Lid geworden op: 23 dec 2017, 19:32
Real name: Marco Albus

Re: Data East small DMD

Bericht door maralb » 04 jan 2018, 10:37

Die displays zijn leuke uitdagingen. Ik heb er al verschillende gerepareerd. Problemen verschillen van kapotte inputlatch, kapotte SRAM en ook vrij vaak een van de displaydrivers, vooral de 5222 is mijn ervaring. Vervelend is wel dat je altijd het glas moet verwijderen als je aan het ding wil werken. Als ik dat doe vervang ik sowieso de, elko's en de socket voor de Eprom (Data East heeft daar echt pulp voor gebruikt), en zet ik de Z80, SRAM en inputbuffer op IC voeten om een eventuele toekomstige reparatie makkelijker te maken. Ook knip ik altijd de uiteinden van de weerstanden kort; die zijn vaak vrij lang gehouden en heel griezelig platgedrukt over naastliggende sporen. Zomaar een greep uit mijn ervaringen.

Er is een mooie manier om het glas te testen:

Testing the Small Dot Matrix Display Glass.
Use this technique to test a new or used small (128x16) dot matrix score glass. This technique uses an existing small dot matrix display panel to test a loose dot matrix score glass. Here is the procedure:
Turn the game off.
Lower the display panel on the game.
Connect a (black) alligator jumper wire from either lead of capacitor C29 (near U15) on the back of the display glass' circuit board.
Connect the other lead of the (black) alligator jumper wire to one of the row pins on the dot matrix glass. This connector puts -100 volts DC on the row the jumper is connected to. NOTE: there are two sets of row pins, on each side of the display glass. Each set corresponds to that half of the display glass.
Connect a (red) alligator jumper to the banded side (cathode) of CR2 on the dot matrix display board (this is a connection to +68 volts DC).
Put a 33k ohm 1/2 watt resistor in the free lead of the red alligator clip.
Turn the game on.
Touch the free end of the resistor (which is connected to the red alligator lead) to one column lead on the display glass. Note the column must be on the same half of the glass as the row connected!
The dot which intersects the row and column should glow.
This test can also be performed for new dot matrix glasses that have not been installed, using the existing dot matrix controller board. For a quick column test, just run the free resistor lead along the column pins. Remember only one side of the row (the side with the row jumper) will work at a time. This was discussed in DataEast's service bulletin number 76.

Groeten vanuit Driebergen ;)

Marco

maralb
Berichten: 128
Lid geworden op: 23 dec 2017, 19:32
Real name: Marco Albus

Re: Data East small DMD

Bericht door maralb » 04 jan 2018, 14:29

En als aanvulling op bovenstaand relaas.....ik ga er vanuit dat voedingsspanningen, kabels en bandkabels in orde zijn; dat zijn dingen die makkelijk te controleren zijn. Kijk ook altijd kritisch naar de IDC connector die het die het display van spanningen voorziet. Daar hangt vaak een zware ferrietkraal aan die de draden nog wel eens los trekt uit de "messen" van de connector.

Marco

Gebruikersavatar
vanlierde51
Berichten: 522
Lid geworden op: 25 feb 2014, 08:32
Real name: Gilles Van Lierde
Locatie: Belgium

Re: Data East small DMD

Bericht door vanlierde51 » 04 jan 2018, 19:56

Ok dank U allemaal. Nu weet ik wat te doen van de we!

Groetjes
Gilflip
BOP, FT, JP, DW, Radical, DrWho, SMania,BSD,DLady,GWings, Space T,GLizard, JITB,Blue Rib,Pharaoh,T-Zone,Pol Force,CBWizard,Bad girls,TM, DM, DW, SK, PB35th- neo-geo 120 in 1, Brabo 60 in 1, Carn-Evil, Offroad Rally

Gebruikersavatar
flippers.be
Berichten: 2200
Lid geworden op: 14 aug 2011, 14:31
Real name: AE
Locatie: Belgium
Contacteer:

Re: Data East small DMD

Bericht door flippers.be » 05 jan 2018, 09:51

Begin met die R95 na te meten en te vervangen :)

Gebruikersavatar
vanlierde51
Berichten: 522
Lid geworden op: 25 feb 2014, 08:32
Real name: Gilles Van Lierde
Locatie: Belgium

Re: Data East small DMD

Bericht door vanlierde51 » 05 jan 2018, 18:40

Inderdaad...geen werkende inserts. Maar ook nergens 18V te bespeuren op de schema....
Waar moet ik die meten? Van waar komt hem?
Gilflip
BOP, FT, JP, DW, Radical, DrWho, SMania,BSD,DLady,GWings, Space T,GLizard, JITB,Blue Rib,Pharaoh,T-Zone,Pol Force,CBWizard,Bad girls,TM, DM, DW, SK, PB35th- neo-geo 120 in 1, Brabo 60 in 1, Carn-Evil, Offroad Rally

Plaats reactie